Chicago Pneumatic Accessories & Parts
More than 1,200 genuine Chicago Pneumatic accessories and service parts — impact sockets, abrasives, 0.401 and 0.498 in. shank chisels, scaler needles, collets, hoses and couplers, FRL units, tool balancers, air-tool oil, and tune-up kits. If a CP tool wears it, breaks it, or bolts to it, it is on this page.
The short version
Two ways in. Know the part → the parts lookup takes the tool model number and finds the exact kit or wear part. Browsing by type → the twelve categories below cover every accessory family we stock. The single cheapest life-extender in the building is genuine CP air-tool oil — a few drops a day roughly doubles vane motor life. Can’t find it → 1-888-883-5144 with the model number off the tool housing.
Every CP Accessory Category
Twelve families, 1,200-plus items, all genuine Chicago Pneumatic. Counts are live catalog totals.
Looking for Chicago Pneumatic Tool Parts?
The parts questions we answer every week — and where each answer lives.
Impact wrench parts
Vanes, hammers, anvils, retainer rings and tune-up kits for CP impact guns, current and legacy.
Parts lookup →Die grinder & angle grinder parts
Collets, bearings, governors, guards and spindles for CP875, CP3xxx industrial and legacy grinders.
Parts lookup →Ratchet parts
Ratchet heads, yokes, pawls and rebuild kits for CP824 through CP7830 air ratchets.
Parts lookup →Riveter & rivet squeezer parts
Pistons, springs, retainers and yokes for CP rivet guns, riveters and squeezers.
Parts lookup →Chipping hammer & scaler parts
Chisels, needles, springs and retainers — most are stocked in percussive accessories.
Shop chisels & needles →Electric drill parts
Legacy CP electric drill parts are identify-by-model — call with the nameplate model and serial.
Call 1-888-883-5144 →CP Parts & Accessories — Common Questions
How do I find the right part for my CP tool?
Start from the model number on the tool housing — not the description. Feed it to our parts lookup or call 1-888-883-5144 and we will pull the parts breakdown, identify the piece, and tell you what else usually wears alongside it (vanes and end plates, for instance, are a pair). Genuine CP parts keep the factory warranty intact.
Are these genuine Chicago Pneumatic parts or aftermarket?
Genuine, bought through the factory channel. Crowder Supply is a stocking CP dealer — the sockets, chisels, collets, and kits here are the same parts CP builds the tools with. Aftermarket copies of high-speed parts like collets and governors are a false economy; a mis-machined collet at 25,000 rpm destroys the tool it was meant to save.
What routine maintenance do CP air tools actually need?
Three habits cover ninety percent of it: a few drops of air-tool oil in the inlet daily, dry regulated air through an FRL, and a tune-up kit when power fades instead of running the tool to destruction. Water in unfiltered air is the number-one vane motor killer we see.
Do you stock impact sockets for the big spline-drive guns?
Impact-rated sockets, extensions, and adapters from 1/4 through 1-1/2 in. drive are in bolting accessories. Chrome hand sockets do not belong on an impact gun — they shatter. For #5 spline sockets and the heavy sizes, call and we will confirm the exact fit for your gun.
Can you get parts for old or discontinued CP tools?
Often, yes — CP maintains parts support for a long tail of legacy tools, and many wear parts interchange across generations. Call 1-888-883-5144 with the model and serial off the nameplate. If the part is genuinely gone, we will say so and quote the closest current tool instead of leaving you guessing.
Need a Part Number Identified?
Call with the model number off the tool housing and we will identify the part, the kit, and what else usually wears with it.